System Too Lean – Bank 1
Description:
How does a P0171 code trigger the check engine light? This code will trigger the check engine light as follows:
The adaptive fuel strategy in the vehicle’s computer constantly monitors the fuel delivery system to make sure the engine is running at an optimum air to fuel ratio, which is 14.7:1. The computer adjusts injector pulse width to regulate the amount of fuel going into the engine. The oxygen sensors relay information to the Powertrain Control Module (computer), informing it of the oxygen content in the exhaust. This information is translated by the computer, and used to determine if more or less fuel is needed. The computer will then adjust fuel flow (and possibly other related engine operating characteristics), to keep the correct air fuel mixture. This loop continues as long as the engine is running. Please refer to our article Oxygen Sensor Code Diagnosis for more info on this system. A P0171 check engine light code is set when the computer has reached a rich calibration limit and can not add enough fuel to maintain the correct mixture.
Possible Causes:
Refer to our Oxygen Sensor Code Diagnosis article for a list of all possible causes. The following is an overview of P0171 check engine light code possible causes.
Fuel System:
Leaking or faulty fuel pressure regulator
Plugged or dirty fuel filter or lines
Fuel pump weak or defective check valve
Injectors leaking or faulty
Low fuel pressure or running out of fuel
Leaking EVAP system components
Faulty FRP (Fuel Rail Pressure Sensor)
Air Intake System
Vacuum leaks
Contaminated, damaged or faulty Mass Air Flow sensor
PCV valve leak or stuck open
Air induction turbulance caused by wrong filter
Oil dipstick not seated
Air leaks after the Mass Air Flow Sensor (MAF)
Oil coated aftermarket air filter
Exhaust System
Any exhaust leak before or near the oxygen sensors
EGR System
Vacuum line disconnected from EGR System Module (ESM)
EGR valve, tube or gasket leak
EGR vacuum regulator valve leaking
Secondary Air Injection System
Mechanically stuck secondary air injection valve
Mass Air Flow (MAF) Circuit Low Input
Description:
How does a P0102 code trigger the check engine light? The engine light will come on if the following concern is present:
The Mass Air Flow Sensor circuit is monitored by the powertrain control module (computer), for low voltage (which translates to low air flow) through the Comprehensive Component Monitor (CCM). With the key on and engine running, if the voltage drops below a minimum value this code will be set, causing the check engine light to illuminate.
Possible Causes:
MAF Sensor disconnected
MAF Sensor circuit open to computer
Vehicle Power circuit open to MAF Sensor
Power Ground circuit open to MAF Sensor
MAF Sensor Return circuit open to PCM
MAF Sensor circuit shorted to Ground
Intake air leak near MAF Sensor
Damaged MAF Sensor
Damaged computer
Diagnostic Help:
Refer to an appropriate manual for specification. If MAF Sensor voltage reading is below minimum limit with key on engine running then concern is a hard fault (present now). If all values are in spec proceed with intermittent diagnosis (refer to our “Intermittent Diagnosis Help” article through the “articles” link on the Navigation Bar). You may also use the “Get Help” link if you need specifications or have any other related questions.
Intake Cam Position Timing Over Retarded – Bank 2
Description:
How does a P0022 code trigger the check engine light? This code will trigger the check engine light under the following condition:
The comprehensive component monitor, referred to as the CCM, monitors the Variable Camshaft Timing (VCT) position for over-retarded cam timing. If the cam timing exceeds a maximum calibrated limit or is stuck in a retarded position, the check engine light will come on and set this trouble code.
Possible Causes:
Incorrect camshaft timing
VCT solenoid valve stuck open or continuous oil flow to piston chamber
Camshaft advance mechanism binding, or faulty VCT unit
Diagnostic Help:
This check engine light code is caused by a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Possible symptoms may include rough idle, stall or hard start. Refer to manufacturer specific component tests for the VCT unit. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instructions.
Intake Cam Position Timing Over Advanced – Bank 2
Description:
How does a P0021 code trigger the check engine light? This code will trigger the check engine light under the following condition:
The comprehensive component monitor, referred to as the CCM, monitors the Variable Camshaft Timing (VCT) position for over-advanced cam timing. If the cam timing exceeds a maximum calibrated limit or is stuck in an advanced position, the check engine light will come on and set this trouble code.
Possible Causes:
Incorrect camshaft timing
VCT solenoid valve stuck open or continuous oil flow to piston chamber
Camshaft advance mechanism binding, or faulty VCT unit
Diagnostic Help:
This check engine light code is caused by a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Possible symptoms may include rough idle, stall or hard start. Refer to manufacturer specific component tests for the VCT unit. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instructions.
Variable Camshaft Timing Over Retarded – Bank 1
Description:
How does a P0012 code trigger the check engine light? This code will trigger the check engine light under the following condition:
The comprehensive component monitor, referred to as the CCM, monitors the Variable Camshaft Timing (VCT) position for over-retarded cam timing. If the cam timing exceeds a maximum calibrated limit or is stuck in a retarded position, the check engine light will come on and set this trouble code.
Possible Causes:
Incorrect camshaft timing
VCT solenoid valve stuck open or continuous oil flow to piston chamber
Camshaft advance mechanism binding, or faulty VCT unit
Diagnostic Help:
This check engine light code is caused by a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Possible symptoms may include rough idle, stall or hard start. Refer to manufacturer specific component tests for the VCT unit. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instructions.
- Reset the Maintenance Light on Dacia SanderoHow to Reset the Maintenance Light on Dacia Sandero: A Detailed Guide Owning a Dacia Sandero comes with the responsibility of ensuring it runs optimally. An essential aspect of this is recognizing and addressing the maintenance reminders. This guide provides instructions on resetting the maintenance light for Dacia Sandero, a crucial step after servicing your […]
- RESET ENGINE OIL LIFE CADILLAC CT6 ON 2014-2017Resetting the Engine Oil Life Indicator for Cadillac CT6 (2014-2017) The Cadillac CT6, a hallmark of luxury and engineering precision, requires meticulous care, especially when it comes to its engine oil. One of the essential aspects of maintaining this vehicle is understanding how to reset the engine oil life indicator. This feature ensures that the […]
- Reset oil life for Hyundai Veloster ON 2014-2017Step-by-Step Guide: Resetting Oil Life on Hyundai Veloster (2014-2017) Maintaining the health of your Hyundai Veloster’s engine is crucial. The vehicle’s oil life monitoring system alerts you when it’s time for an oil change. If you have a Hyundai Veloster from the years 2014 through 2017, follow this guide to reset the oil life indicator […]
- Reset Oil Change Warning Light for Dacia Duster 2009-2015Step-by-Step Guide: Resetting the Oil Change Warning Light for Dacia Duster (2009-2015) Do you own a 2009-2015 Dacia Duster? Then, knowing how to reset its oil change warning light is crucial. This light reminds you when to change the engine oil, ensuring peak performance for your vehicle. In this guide, we’ll walk you through the […]
- Service light reset dashboard BMW X5 and BMW X6How do you reset maintenance light, reset service light indicator BMW X5 and BMW X6, year 2000-2013. For reset maintenance light and that can be made manually by use button on car dashboard. Reset oil service light, engine oil life BMW X5 and BMW X6, year 2000-2013 oil reset instructions: Turn the ignition to the […]