Lamp

Check Engine Light Code P0040

Upstream O2 Sensors Swapped Bank To Bank

Description:

How does a P0040 code trigger the check engine light? This code will trigger the light to come on under the following condition:

The Heated Oxygen Sensor Monitor, a strategy built into the computer, determines if the Heated Oxygen Sensor (HO2S) signal response for a change in fuel trim corresponds to the correct engine bank. If a response from the Oxygen Sensor being tested is not indicated, a trouble code will be set and the MIL (Malfunction Indicator Lamp) will illuminate.

Possible Causes:

Crossed Heated Oxygen Sensor harness connectors
Wiring swapped from one Oxygen Sensor connector to the other
Wiring changed at the computer connection or in the related harness

Diagnostic Help:

This check engine light code is caused by swapped wiring or connectors of the upstream Heated Oxygen Sensors. This would have to be the result of a previous repair, so be sure to check the vehicle history. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instructions.

Posted in Check Engine Light Code | Tagged Bank, Causes, change, Check, check engine, check engine light, Code, Computer, Condition, connection, connector, Crossed, Description, Diagnostic, Engine, engine error codes, Fuel, harness, Heated, history, Indicator, Lamp, Light, Link, Malfunction, Malfunction indicator lamp, monitor, Oxygen, Oxygen Sensor, Oxygen Sensors, repair, Response, result, Sensor, Sensors, Signal, strategy, Swapped, Trouble, Upstream, Vehicle, wiring

P08XX Transmission

P0801 Reverse Inhibit Control Circuit
P0803 1-4 Upshift (Skip Shift) Solenoid Control Circuit
P0804 1-4 Upshift (Skip Shift) Lamp Control Circuit
P0805 Clutch Position Sensor Circuit
P0806 Clutch Position Sensor Circuit Range/Performance
P0807 Clutch Position Sensor Circuit Low
P0808 Clutch Position Sensor Circuit High
P0809 Clutch Position Sensor Circuit Intermittent
P0810 Clutch Position Control Error
P0811 Excessive Clutch Slippage
P0812 Reverse Input Circuit
P0813 Reverse Output Circuit
P0814 Transmission Range Display Circuit
P0815 Upshift Switch Circuit
P0816 Downshift Switch Circuit
P0817 Starter Disable Circuit
P0818 Driveline Disconnect Switch Input Circuit

P0820 Gear Lever X-Y Position Sensor Circuit
P0821 Gear Lever X Position Circuit
P0822 Gear Lever Y Position Circuit
P0823 Gear Lever X Position Circuit Intermittent
P0824 Gear Lever Y Position Circuit Intermittent
P0825 Gear Lever Push-Pull Switch (Shift Anticipate)

P0830 Clutch Pedal Switch “A” Circuit
P0831 Clutch Pedal Switch “A” Circuit Low
P0832 Clutch Pedal Switch “A” Circuit High
P0833 Clutch Pedal Switch “B” Circuit
P0834 Clutch Pedal Switch “B” Circuit Low
P0835 Clutch Pedal Switch “B” Circuit High
P0836 Four Wheel Drive (4WD) Switch Circuit
P0837 Four Wheel Drive (4WD) Switch Circuit Range/Performance
P0838 Four Wheel Drive (4WD) Switch Circuit Low
P0839 Four Wheel Drive (4WD) Switch Circuit High
P0840 Transmission Fluid Pressure Sensor/Switch “A” Circuit
P0841 Transmission Fluid Pressure Sensor/Switch “A” Circuit Range/Performance
P0842 Transmission Fluid Pressure Sensor/Switch “A” Circuit Low
P0843 Transmission Fluid Pressure Sensor/Switch “A” Circuit High
P0844 Transmission Fluid Pressure Sensor/Switch “A” Circuit Intermittent
P0845 Transmission Fluid Pressure Sensor/Switch “B” Circuit
P0846 Transmission Fluid Pressure Sensor/Switch “B” Circuit Range/Performance
P0847 Transmission Fluid Pressure Sensor/Switch “B” Circuit Low
P0848 Transmission Fluid Pressure Sensor/Switch “B” Circuit High
P0849 Transmission Fluid Pressure Sensor/Switch “B” Circuit Intermittent

Posted in OBD II Fault Codes | Tagged Anticipate, check engine, Circuit, Circuit Intermittent, Clutch, Clutch Pedal, Clutch Position Sensor Circuit, Control, Control Circuit, Disable, Disconnect, Display, Downshift, Drive, Driveline, engine error codes, Error, Excessive, Fluid, Four, Gear, High, Inhibit, Input, Input Circuit, Intermittent, Lamp, Lamp Control Circuit, Lever, Low, Malfunction indicator lamp, Output, Output Circuit, Pedal, Performance, Position, Pressure, Pull, Rang, Reverse, Sensor, Shift, Skip, Slippage, Solenoid, Starter, Switch, Switch Circuit, Transmission, Transmission Fluid, Upshift, Wheel

P06XX Computer and Auxiliary Inputs

P0600 Serial Communication Link
P0601 Internal Control Module Memory Check Sum Error
P0602 Control Module Programming Error
P0603 Internal Control Module Keep Alive Memory (KAM) Error
P0604 Internal Control Module Random Access Memory (RAM) Error
P0605 Internal Control Module Read Only Memory (ROM) Error

P0606 ECM/PCM Processor
P0607 Control Module Performance
P0608 Control Module VSS Output “A”
P0609 Control Module VSS Output “B”
P0610 Control Module Vehicle Options Error

P0615 Starter Relay Circuit
P0616 Starter Relay Circuit Low
P0617 Starter Relay Circuit High
P0618 Alternative Fuel Control Module KAM Error
P0619 Alternative Fuel Control Module RAM/ROM Error
P0620 Generator Control Circuit
P0621 Generator Lamp “L” Terminal Control Circuit
P0622 Generator Field “F” Terminal Control Circuit
P0623 Generator Lamp Control Circuit
P0624 Fuel Cap Lamp Control Circuit

P0630 VIN Not Programmed or Mismatch – ECM/PCM
P0631 VIN Not Programmed or Mismatch – TCM

P0635 Power Steering Control Circuit
P0836 Power Steering Control Circuit Low
P0637 Power Steering Control Circuit High
P0638 Throttle Actuator Control Range/Performance (Bank 1)
P0639 Throttle Actuator Control Range/Performance (Bank 2)
P0640 Intake Air Heater Control Circuit

P0645 A/C Clutch Relay Control Circuit
P0646 A/C Clutch Relay Control Circuit Low
P0647 A/C Clutch Relay Control Circuit High
P0648 Immobilizer Lamp Control Circuit (“Immobilizer” pending SAE J1930 approval)
P0649 Speed Control Lamp Control Circuit
P0650 Malfunction Indicator Lamp (ML) Control Circuit

P0654 Engine RPM Output Circuit
P0655 Engine Hot Lamp Output Control Circuit
P0656 Fuel Level Output Circuit

P0660 Intake Manifold Tuning Valve Control Circuit (Bank 1)
P0661 Intake Manifold Tuning Valve Control Circuit Low (Bank 1)
P0662 Intake Manifold Tuning Valve Control Circuit High (Bank 1)
P0663 Intake Manifold Tuning Valve Control Circuit (Bank 2)
P0664 Intake Manifold Tuning Valve Control Circuit Low (Bank 2)
P0665 Intake Manifold Tuning Valve Control Circuit High (Bank 2)

Posted in OBD II Fault Codes | Tagged Access, Actuator, Air, Alive, Alternative, approval, Auxiliary, Bank, Cap, Cap Lamp Control Circuit, Check, check engine, Circuit, Clutch Relay Control Circuit High P0648 Immobilizer Lamp Control Circuit, Communication, Computer, Control, Control Circuit, Control Module, ECM, Engine, engine error codes, Error, Field, Fuel, Generator, Generator Control Circuit, Heater, High, Hot, Immobilizer, Indicator, Inputs, Intake, Internal, Internal Control, Internal Control Module, KAM, Lamp, Lamp Control Circuit, Level, Link, Low, Malfunction, Malfunction indicator lamp, manifold, Memory, Mismatch, Module, Output, Output Circuit, P0615 Starter Relay, P0616 Starter Relay, P0617 Starter Relay, P0660 Intake Manifold, P0661 Intake Manifold, P0662 Intake Manifold, P0663 Intake Manifold, P0664 Intake Manifold, P0665 Intake Manifold, PCM, Performance, Power, Processor, Programmed, Programming, RAM, Random, Range, Relay, ROM, RPM, SAE, Speed Control Lamp Control Circuit, Starter, Steering, Sum, TCM, Terminal, Terminal Control Circuit, Throttle, Tuning, Valve, Vehicle, VSS