Misfire Detection Monitor – Cylinder 12 Misfire

Description:

How does a P0312 code trigger the check engine light? This code will trigger the check engine light as follows:

The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we are left with a P0312 in the computer memory.

Possible Causes:

Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Diagnostic Help:

To diagnose a P0312 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article “Automotive Circuit Testing 101”, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.

Misfire Detection Monitor – Cylinder 11 Misfire

Description:

How does a P0311 code trigger the check engine light? This code will trigger the check engine light as follows:

The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we are left with a P0311 in the computer memory.

Possible Causes:

Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Diagnostic Help:

To diagnose a P0311 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article “Automotive Circuit Testing 101”, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.

Misfire Detection Monitor – Cylinder 10 Misfire

Description:

How does a P0310 code trigger the check engine light? This code will trigger the check engine light as follows:

The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we are left with a P0310 in the computer memory.

Possible Causes:

Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Diagnostic Help:

To diagnose a P0310 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article “Automotive Circuit Testing 101”, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.

Misfire Detection Monitor – Cylinder 9 Misfire

Description:

How does a P0309 code trigger the check engine light? This code will trigger the check engine light as follows:

The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we are left with a P0309 in the computer memory.

Possible Causes:

Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Diagnostic Help:

To diagnose a P0309 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article Automotive Circuit Testing 101, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.

Misfire Detection Monitor – Cylinder 8 Misfire

Description:

How does a P0308 code trigger the check engine light? This code will trigger the check engine light as follows:

The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we are left with a P0308 in the computer memory.

Possible Causes:

Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Diagnostic Help:

To diagnose a P0308 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article “Automotive Circuit Testing 101”, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the “Get Help” link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.

Recent Comments
  • Reset the Maintenance Light on Dacia Sandero
    How to Reset the Maintenance Light on Dacia Sandero: A Detailed Guide Owning a Dacia Sandero comes with the responsibility of ensuring it runs optimally. An essential aspect of this is recognizing and addressing the maintenance reminders. This guide provides instructions on resetting the maintenance light for Dacia Sandero, a crucial step after servicing your […]
  • RESET ENGINE OIL LIFE CADILLAC CT6 ON 2014-2017
    Resetting the Engine Oil Life Indicator for Cadillac CT6 (2014-2017) The Cadillac CT6, a hallmark of luxury and engineering precision, requires meticulous care, especially when it comes to its engine oil. One of the essential aspects of maintaining this vehicle is understanding how to reset the engine oil life indicator. This feature ensures that the […]
  • Reset oil life for Hyundai Veloster ON 2014-2017
    Step-by-Step Guide: Resetting Oil Life on Hyundai Veloster (2014-2017) Maintaining the health of your Hyundai Veloster’s engine is crucial. The vehicle’s oil life monitoring system alerts you when it’s time for an oil change. If you have a Hyundai Veloster from the years 2014 through 2017, follow this guide to reset the oil life indicator […]
  • Reset Oil Change Warning Light for Dacia Duster 2009-2015
    Step-by-Step Guide: Resetting the Oil Change Warning Light for Dacia Duster (2009-2015) Do you own a 2009-2015 Dacia Duster? Then, knowing how to reset its oil change warning light is crucial. This light reminds you when to change the engine oil, ensuring peak performance for your vehicle. In this guide, we’ll walk you through the […]
  • Service light reset dashboard BMW X5 and BMW X6
    How do you reset maintenance light, reset service light indicator BMW X5 and BMW X6, year 2000-2013. For reset maintenance light and that can be made manually by use button on car dashboard. Reset oil service light, engine oil life BMW X5 and BMW X6, year 2000-2013 oil reset instructions: Turn the ignition to the […]